Nhanganyaya
This manual provides detailed instructions for the installation, operation, and maintenance of your Project Source Chrome 1-Handle Pull-Down Kitchen Faucet, model 51-K814-PS-CP. Please read this manual thoroughly before beginning installation and retain it for future reference.
Safety Information
- Nguva dzose dzimai mvura huru musati maisa kana kugadzirisa pombi.
- Wear safety glasses and gloves during installation to prevent injury.
- Ita shuwa kuti zvese zvinongedzo zvakachengeteka kudzivirira kuvuza.
- Kana usina chokwadi nezvechikamu chipi zvacho chekuisa, bvunza nyanzvi yepombi.
Package Zviri mukati
Tarisa kuti zvese zviriko zviripo usati watanga kuisa:
Mufananidzo 1: All components of the Project Source pull-down kitchen faucet, including the main faucet body, hot and cold water supply lines, mounting hardware, deck plate, and instruction manual.
- Main Faucet Body with Pull-Down Sprayer
- Hot and Cold Water Supply Lines (pre-attached)
- Mounting Hardware (nut, washer, gasket)
- Deck Plate (optional, for 3-hole sinks)
- Weight (for pull-down hose)
- Bhuku reMirayiridzo
Setup uye Installation
Zvishandiso Zvinodiwa:
- Adjustable Wrench
- Phillips Musoro Screwdriver
- Putty yePlumber kana Silicone Sealant
- Bucket (for catching drips)
- Tochi
Kuisa Matanho:
- Gadzirira Sink: Turn off the hot and cold water supply valves under the sink. Open the existing faucet to drain any remaining water. Disconnect and remove the old faucet. Clean the sink surface thoroughly.
- Install Deck Plate (Optional): If your sink has three holes, place the deck plate (if using) over the sink holes. Apply a thin bead of plumber's putty or silicone sealant around the underside edge of the deck plate to create a watertight seal.
- Mount the Faucet: Insert the faucet body through the center hole of the sink (and deck plate, if used). From underneath the sink, slide the rubber washer, then the metal washer, and finally thread the mounting nut onto the faucet shank. Hand-tighten, then use an adjustable wrench to secure it firmly, ensuring the faucet is properly aligned.
- Batanidza Mitsetse Yekupa Mvura: Connect the hot and cold water supply lines from the faucet to the corresponding hot and cold water supply valves. The faucet's lines are typically labeled (e.g., "HOT" for hot water). Hand-tighten, then use an adjustable wrench for a final quarter-turn. Do not overtighten.
- Install Hose Weight: Locate the indicator on the pull-down hose (usually a sticker or mark) where the weight should be installed. Attach the provided weight to the pull-down hose at this indicated position. This weight helps the sprayer retract smoothly.
- Tarisa uone Mavuza: Slowly turn on the hot and cold water supply valves. Check all connections for leaks. If leaks are present, tighten the connections slightly until the leak stops.
- Bvisa pombi: Remove the sprayer head and turn on the faucet to flush out any debris from the lines. Let the water run for a few minutes. Turn off the faucet, reattach the sprayer head, and check for proper operation.
Operating Instruction
- Kuyerera kweMvura uye Tembiricha: The single handle controls both water flow and temperature. Lift the handle to increase water flow. Move the handle to the left for hot water and to the right for cold water.
- Pull-Down Sprayer: Grasp the sprayer head and pull it down from the spout. The hose will extend to allow for greater reach. Press the button on the sprayer head to switch between stream and spray functions. When finished, guide the sprayer head back into the spout; the hose weight will assist in retraction.
Maintenance
- Kuchenesa: Chenesa pombi nguva dzose nejira rakapfava nesipo isina kunyorova. Dzivisa mishonga inokwesha, makemikari akaomarara, kana mapedhi ekukwesha, sezvo izvi zvinogona kukuvadza chrome finish.
- Kuchenesa Aerator: If water flow decreases, the aerator may be clogged. Unscrew the aerator from the tip of the sprayer head, clean any debris, and rinse thoroughly before reattaching.
- Hose Weight Adjustment: If the pull-down sprayer does not retract smoothly, check the position of the hose weight. Adjust its position along the hose as needed to ensure proper retraction.
Kugadzirisa matambudziko
| Dambudziko | Zvinogona Kukonzera | Solution |
|---|---|---|
| Kuyerera Kwemvura Yakaderera | Aerator yakavharika; mavharuvhu emagetsi akavharwa zvishoma. | Clean aerator; fully open supply valves. |
| Kubuda kwemvura paConnections | Loose connections; damaged washers. | Tighten connections; replace washers if damaged. |
| Sprayer Does Not Retract | Hose weight is misplaced or missing; obstruction. | Adjust or reattach hose weight; clear any obstructions. |
| Dripping Faucet | Katuriji yakasakara. | Contact customer support for cartridge replacement. |
Zvinotsanangurwa
| Feature | Detail |
|---|---|
| Model Number | 51-K814-PS-CP |
| Brand | Project Source |
| Color | Chrome |
| Style | Contemporary |
| Finish | Yakanatswa |
| Material | Ceramic (yekaturiji) |
| Installation Method | Mumwe Hole |
| Flow Rate | 1.8 Maroni Paminiti |
| Nhamba yeMaholo | 1 |
| Mounting Type | Dhiza Gomo |
| Special Features | Dhonza Pazasi Sprayer |
| Product Dimensions | 27.43 x 8.64 x 64.52 cm |
| Item Weight | 2.34 kg |
Warranty uye Support
For warranty information or technical support, please refer to the contact details provided with your purchase documentation or visit the official Project Source website. Chengetedza risiti yako yekutenga sehumbowo hwekutenga kwezvichemo zvewaranti.
