Boardcon Yakamisikidzwa CM1126B-P System paModule
Zvinotsanangurwa
| Feature | Zvinotsanangurwa |
| CPU | Quad-core Cortex-A53 |
| DDR | 2GB LPDDR4 (kusvika ku4GB) |
| eMMC FLASH | 8GB (kusvika ku256GB) |
| Simba | DC 3.3V |
| MIPI DSI | 4-Lane |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-Lane |
| RGB LCD | 24bit |
| Kamera | 1-CH(DVP) uye 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 uye OTG 2.0) |
| Ethernet | 1000M GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Board Dimension | 34 x 35mm |
Nhanganyaya
Pamusoro peBhuku rino
Bhuku rino rinoitirwa kupa mushandisi mukana wekupfuuraview yebhodhi nemabhenefiti ayo, yakazara maficha ezvimiro, uye kuseta maitiro. Iine ruzivo rwakakosha rwekuchengetedza zvakare.
Mhinduro uye Kugadziridza kuBhuku rino
Kuti tibatsire vatengi vedu kuita zvakanyanya zvigadzirwa zvedu, tiri kuramba tichigadzira zvimwe uye zvakagadziridzwa zviwanikwa zviripo paBoardcon websaiti (www.boardcon.com, www.armdesigner.com) Izvi zvinosanganisira zvinyorwa, zvinyorwa zvekushandisa, programming examples, uye yakagadziridzwa software uye hardware. Tarisa nguva nenguva kuti uone zvitsva! Kana isu tiri kukoshesa basa pane izvi zvakagadziridzwa zviwanikwa, mhinduro kubva kune vatengi ndiyo yekutanga pesvedzero, Kana uine mibvunzo, makomendi, kana kunetsekana nezve chigadzirwa chako kana chirongwa, ndapota usazeza kutibata pa support@armdesigner.com.
CM1126B-P Nhanganyaya
Summary
Iyo CM1126B-P system-on-module ine Rockchip's RV1126B-P, yakavakwa nequad-core Cortex-A53, 3.0 TOPs NPU, uye RISC-V MCU. Yakagadzirirwa chaizvo IPC/CVR zvishandiso, AI Kamera zvishandiso, zvine hungwaru zvinopindirana zvishandiso, uye mini marobhoti. Yepamusoro-inoshanda uye yakaderera-simba mhinduro inogona kubatsira vatengi kuunza matekinoroji matsva nekukurumidza uye kuwedzera iyo yakazara mhinduro kushanda. Iyo diki saizi inogona kuiswa pa38board. Kutevera kudzokororwa kwehardware kubva kuCM1126 (V1) kuenda kuCM1126B-P (V2), uko SoC inogadziridzwa kuRV1126B-P, iyo Reset & OTG_VBUS masaini uye WIFI/BT module's GPIO vol.taginofanira kushanda pa 3.3V logic level.
Features
Microprocessor
- Quad-core Cortex-A53 kusvika ku1.6GHz
- 32KB I-cache uye 32KB D-cache yega yega musimboti, 512KB L3 cache
- 3.0 TOPS Neural Process Unit
- RISC-V MCU kutsigira 250ms nekukurumidza bhutsu
- Max 12M ISP
Memory Organization
- LPDDR4 RAM kusvika ku4GB
- eMMC kusvika ku256GB
- SPI Flash inosvika ku8MB
Vhidhiyo Decoder/Encoder
- Inotsigira vhidhiyo decode/encode kusvika ku4K@30fps
- Inotsigira real-time decoding yeH.264/265
- Inotsigira real-time UHD H.264/265 video encoding
- Mufananidzo saizi kusvika 8192 × 8192
Ratidza Subsystem
- Video Output
- Inotsigira 4 nzira MIPI DSI kusvika 2560 × 1440@60fps
- Inotsigira 24-bit RGB parallel kubuda
- Mufananidzo mu
- Inotsigira kusvika ku16-bit DVP interface
- Inotsigira 2ch MIPI CSI 4lanes interface
I2S/PCM/AC97
- Matatu I2S/PCM interface
- Tsigira Mic array Kusvika ku8ch PDM/TDM interface
- Tsigira PWM odhiyo kubuda
USB uye PCIE
- Maviri 2.0 USB interfaces
- Imwe USB 2.0 OTG uye imwe 2.0 USB host
Ethernet
- RTL8211F pabhodhi
- Tsigira 10/100/1000M
I2C
- Kusvikira kushanu I2Cs
- Tsigira yakajairika modhi uye nekukurumidza maitiro (kusvika ku400kbit / s)
SDIO
- Tsigira 2CH SDIO 3.0 protocol
SPI
- Kusvikira kune maviri SPI controller,
- Yakazara-duplex synchronous serial interface
UART
- Tsigira kusvika ku6 UARTs
- UART2 ine waya mbiri dzematurusi ekugadzirisa
- Yakaiswa maviri 664-byte FIFOs
- Tsigira otomatiki kuyerera kwekudzora maitiro eUART0/1/3/4/5
ADC
- Kusvikira mana ADC chiteshi
- 12-bit kugadzirisa
- Voltage yekupinda pakati pe0V kusvika 1.8V
- Tsigira kusvika ku1MS/ssampling rate
PWM
- 11 pa-chip PWMs ine kukanganisa-kwakavakirwa kushanda
- Tsigira 32-bit nguva / counter nzvimbo
- IR sarudzo paPWM3/7
Power unit
- Discrete Power pabhodhi
- Single 3.3V inopinza
CM1126B-P Chivharo Dhidhiyo
RV1126B-P Chivharo Dhidhiyo
Development board (Idea1126) Block Diagram
CM1126B-P PCB Dimension
CM1126B-P Pin Tsanangudzo
| Pin | Signal | Tsanangudzo kana mabasa | GPIO serial | IO Voltage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Ground | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Zvekugadzirisa | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Zvekugadzirisa | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pin | Signal | Tsanangudzo kana mabasa | GPIO serial | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Ground | 0V | |
| 32 | OTG_DP | Inogona kushandiswa kudhawunirodha | 1.8V | |
| 33 | OTG_DM | Inogona kushandiswa kudhawunirodha | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Main Power kupinza | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Main Power kupinza | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Inofanira kushandiswa kune SD Card | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | RTC wachi kubuda | GPIO0_A2_u | 3.3V(V2) |
| 42 | nRESET | Gadzirisa makiyi ekuisa | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
MIPI CSI0 kana LVDS0 kuisa | 1.8V |
| Pin | Signal | Tsanangudzo kana mabasa | GPIO serial | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
MIPI CSI0 kana LVDS0 kuisa | 1.8V | |
| 53 | GND | Ground | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
MIPI CSI1 kana LVDS1 kuisa | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Ground | 0V | |
| 71 | LED1/CFG_LDO0 | Ethernet LINK LED | 3.3V | |
| 72 | LED2/CFG_LDO1 | Ethernet SPEED LED | 3.3V | |
| 73 | MDI0 + | Ethernet MDI chiratidzo | 1.8V | |
| 74 | WDC0- | Ethernet MDI chiratidzo | 1.8V | |
| 75 | MDI1 + | Ethernet MDI chiratidzo | 1.8V | |
| 76 | WDC1- | Ethernet MDI chiratidzo | 1.8V | |
| 77 | MDI2 + | Ethernet MDI chiratidzo | 1.8V | |
| 78 | WDC2- | Ethernet MDI chiratidzo | 1.8V | |
| 79 | MDI3 + | Ethernet MDI chiratidzo | 1.8V | |
| 80 | WDC3- | Ethernet MDI chiratidzo | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pin | Signal | Tsanangudzo kana mabasa | GPIO serial | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Ground | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | ADC yekuisa | 1.8V | |
| 114 | ADCIN2 | ADC yekuisa | 1.8V | |
| 115 | ADCIN1 | ADC yekuisa | 1.8V | |
| 116 | ADKEY_IN0 | Recovery mode set (10K PU) | 1.8V | |
| 117 | GND | Ground | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Pin | Signal | Tsanangudzo kana mabasa | GPIO serial | IO Voltage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Cherechedza:
1. Mazhinji GPIO voltage i 1.8V, asi mamwe mapini akaiswa 3.3V. 2. GPIO voltage shanduko kuenda ku3.3V kune yakamaka (V2). |
||||
Development Kit (Idea1126)
Hardware Design Guide
Peripheral Circuit Reference
Main Power Circuit
Debug Circuit
USB OTG Interface Circuit
PCB Footprint
Product Electrical Characteristics
Dissipation uye Tembiricha
| Symbol | Parameter | Min | Typ | Max | Unit |
| VCC3V3_SYS | System IO
Voltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | VCC3V3_SYS yekuisa Zvazvino | 850 | mA | ||
| Ta | Operating Temperature | -20 | 70 | °C | |
| Tsg | Storage Temperature | -40 | 85 | °C |
Kuvimbika kweMuedzo
| High Temperature Operating Test | ||
| Zviri mukati | Kushanda 8h mukupisa kwakanyanya | 55°C±2°C |
| Mhedzisiro | TBD |
| Operating Life Test | ||
| Zviri mukati | Kushanda mumba | 120h |
| Mhedzisiro | TBD |
Yakakwana Warranty
Boardcon inobvumidza kuti chigadzirwa ichi chive chisina chakakanganisika muzvinhu uye kugadzira kwegore kubva pazuva rekutenga. Munguva ino yewaranti, Boardcon ichagadzirisa kana kutsiva iyo yakaremara nemaitiro anotevera: Ikopi yeinivhoisi yepakutanga inofanirwa kuverengerwa pakudzosera iyo yakaremara unit kuBoardcon. Waranti iyi ine zvishoma haivharise kukuvadzwa kunokonzerwa nemheni kana mamwe mabhizi emagetsi, kushandisa zvisizvo, kushungurudzwa, mamiriro ekushanda asina kujairika, kana kuedza kuchinja kana kugadzirisa basa rechigadzirwa. Iyi waranti inogumira pakugadzirisa kana kutsiviwa kweiyo yakaremara unit. Hapana chiitiko kana Boardcon ichave nemhosva kana kukanganisa chero kurasikirwa kana kukuvadzwa, kusanganisira asi kusingaganhurirwe kune chero yakarasika purofiti, zvikaitika kana zvakakonzeresa kukuvadza, kurasikirwa kwebhizinesi, kana fungidziro yepurofiti inobva mukushandiswa kana kusakwanisa kushandisa chigadzirwa ichi. Kugadziriswa kwakaitwa mushure mekupera kwenguva yewaranti kunoenderana nemutengo wekugadzirisa uye mutengo wekudzoka kutumira. Ndokumbira ubate Boardcon kuronga chero basa rekugadzirisa uye kuti uwane ruzivo rwekuchaja.
FAQs
Mubvunzo: Ndinokwidziridza sei DDR ndangariro paCM1126B-P?
A: Iyo CM1126B-P inotsigira kusvika ku4GB LPDDR4 ndangariro. Kuti uvandudze, simbisa kuenderana nezvakatemwa uye uteedzere maitiro anokurudzirwa.
Mubvunzo: Chii chinodiwa magetsi emagetsi eCM1126B-P?
A: Simba rinodiwa paCM1126B-P ndiro DC 3.3V. Ita shuwa kuti unopa yakagadzikana magetsi ekupa mukati meiyi renji kuitira kuita kwakaringana.
Mubvunzo: Ndinogona kuwedzera simba rekuchengetedza eMMC paCM1126B-P?
A: Hongu, iyo eMMC yekuchengetedza paCM1126B-P inogona kuwedzerwa kusvika ku256GB. Ita shuwa kuenderana neanotsigirwa ekuchengetedza zvishandiso usati wakwidziridza.
Zvinyorwa / Zvishandiso
 |
Boardcon Yakamisikidzwa CM1126B-P System paModule [pdf] User Manual V2.20250422, CM1126B-P Sisitimu paModule, CM1126B-P, Sisitimu paModule, Module |