R27 V2 Zone Programmer
“
Zvinotsanangurwa
- Simba rekushandisa: 230VAC
- Ambient Temperature: Auto Off
- Zviyero: 161mm x 31mm x 100mm
- Contact Rating: British System Standard 2 (Kupokana ne
voltaguye surge 2000V; maererano ne EN60730) - Chirongwa cheMemory Temperature Sensor: Kirasi A
- Backlight: Yakadzima
- IP Rating: MVURA INOPITSA
- Bhatiri: Yakadzima
- Backplate: EPH Controls Ltd.
- Dhigirii rekusvibisa: 3
- Software Kirasi: EP Controls Ltd.
Mirayiridzo Yekushandiswa Kwechigadzirwa
Mounting & Installation
Chenjero! Kuisa uye kubatana kunofanira kuitwa chete
nemunhu anokwanisa. Vagadziri vemagetsi vanokwanisa chete kana vane mvumo
vashandi vebasa vanobvumidzwa kuvhura iyo programmer. Kana iyo
programmer inoshandiswa nenzira isina kutaurwa nemugadziri, its
kuchengeteka kunogona kukanganisa. Usati wamisa programmer, ndizvo
zvinodiwa kuti upedze ese anodiwa marongero anotsanangurwa mune ino
chikamu. Usati watanga kuisa, mugadziri anofanira kunge ari
yekutanga yakabviswa kubva kune mains.
Iyi programmer inogona kukwidzwa pamusoro kana kuisirwa kune yakadzoreredzwa
conduit box.
- Bvisa programmer kubva pakurongedzerwa kwayo.
- Sarudza nzvimbo yekumisikidza yemugadziri:
- Isa iyo programmer 1.5 metres kumusoro kwepasi.
- Dzivirira kuratidzwa kwezuva kana kumwe kupisa / kutonhora
sources.
- Shandisa philips screwdriver kusunungura screws yebackplate
pazasi pemugadziri. Iyo programmer inosimudzwa kumusoro
kubva pasi uye kubviswa kubva kumashure.
Operating Instruction
Kurumidza Kusuma kune yako R27 V2 programmer
…
Mode Selection
…
Programming Modes
…
Factory Program Settings
…
Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi
…
Reviewkuisa Zvirongwa zvePurogiramu
…
Boost Function
…
Basa repamberi
…
…
P01 Kuisa Zuva, Nguva uye Chirongwa Chekuita
…
P02 Holiday Mode
…
P03 Frost Dziviriro
…
P04 Zone Title
…
P05 PIN
…
Copy Basa
…
Backlight Mode Sarudzo
…
Kukiya Keypad
…
Resetting the Programmer
…
Master Reset
…
Nguva Yebasa
…
Mibvunzo Inowanzo bvunzwa (FAQ)
Q: Ndiani anofanira kuita kugadzwa kweR27 V2
programmer?
A: Vagadziri vemagetsi vanokwanisa chete kana vashandi vane mvumo yebasa
inofanira kuita kuiswa kweiyo R27 V2 programmer.
Mubvunzo: Ko iyo programmer inogona kuiswa muzuva rakananga here?
A: Zvinokurudzirwa kudzivirira kuratidzwa zvakananga kuchiedza chezuva kana
kuisa purogiramu.
Mubvunzo: Ndingaita sei kuti ndigadzirise purogiramu?
A: Iyo programmer inogona kusetwa zvakare uchishandisa iyo Master Reset basa
sezvinotsanangurwa mumirairo yekushanda.
"`
R27 V2
2 Zone Programmer Kuisa uye Operating Guide
Tafura yezviri mukati
Installation Instructions
Factory Default Settings
3
Zvinotsanangurwa
3
Chiratidziro cheLCD
4
Bhatani Tsanangudzo
5
Wiring Diagram
6
Mounting & Installation
7
Operating Instruction
Kurumidza Kusuma kune yako R27 V2 programmer
10
Mode Selection
11
Programming Modes
12
Factory Program Settings
12
Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi
13
Reviewkuisa Zvirongwa zvePurogiramu
14
Boost Function
14
Basa repamberi
15
Mirayiridzo Yekushanda Inoenderera mberi
Menu Basa
16
P01 Kuisa Zuva, Nguva uye Chirongwa Chekuita
16
P02 Holiday Mode
17
P03 Frost Dziviriro
18
P04 Zone Title
19
P05 PIN
20
Copy Basa
22
Backlight Mode Sarudzo
23
Kukiya Keypad
24
Resetting the Programmer
24
Master Reset
25
Nguva Yebasa
25
2 Zone Programmer Installation Instructions
Factory Default Settings
Contacts: Chirongwa: Backlight: Keypad Kiya: Frost Dziviriro:
230VAC 5/2D On Off Off
Operating Mode: Pin Lock: Service Interval: Zone Title:
Zvinotsanangurwa
Power Supply: Ambient Temperature: Dimensions: Contact Rating: Chirongwa Memory Temperature Sensor: Backlight: IP Rating: Battery:
230VAC 0 … 50°C 161 x 100 x 31 mm 3(1)A Makore mashanu NTC 5K White IP100 20VDC Lithium LIR3 & CR2032
Backplate: Dhigirii rekusvibisa:
Software Kirasi:
EPH Controls Ltd.
Auto Off Off MVURA INOPITSA
British System Standard 2 (Kupikisa voltaguye surge 2000V; maererano neEN60730) Kirasi A
3
Chiratidziro cheLCD
[1] Inoratidza nguva iripo. [2] Inoratidza zuva razvino revhiki. [3] Inoratidza kana kudzivirira kwechando kwaitwa. [4] Inoratidza kana keypad yakavharwa. [5] Inoratidza zuva razvino. [6] Inoratidza zita renzvimbo. [7] Inoratidza ikozvino modhi.
4
R27V2
Bhatani Tsanangudzo
Boost Button Boost
Bhatani reMenu
MENU
Chirongwa Advance Plus Minus Bhatani Bhatani Bhatani
PROG
ADV
Zone Sarudza Bhatani
Sarudza
OK Bhatani
OK
Master Reset
EPH Controls Ltd.
5
Wiring Diagram
ZONE ZONE ZONE
1
2
1
2
Bvisa OFF ON ON
NL
200-240V~ 50/60Hz
Terminal Connections
Nyika
N
Kwaakarerekera
L
Rarama
1
Zone 1 OFF - N/C Kazhinji yakavharwa kubatana
2
Zone 2 OFF - N/C Kazhinji yakavharwa kubatana
3
Zone 1 ON - N / O Kazhinji yakavhurika yekubatanidza
4
Zone 2 ON - N / O Kazhinji yakavhurika yekubatanidza
6
R27V2
Mounting & Installation
161
31
100
EPH Controls Ltd.
7
Mounting & Installation yakaenderera mberi
Chenjero!
Kuiswa uye kubatana kunofanirwa kuitwa chete nemunhu ane hunyanzvi. Vagadziri vemagetsi vanokwanisa chete kana vashandi vane mvumo yebasa vanotenderwa kuvhura mugadziri. Kana iyo programmer ikashandiswa nenzira isina kutaurwa nemugadziri, kuchengetedza kwayo kunogona kukanganisa. Usati wamisa mugadziri, zvinodikanwa kuti upedze ese anodiwa marongero anotsanangurwa muchikamu chino. Asati atanga kuisa, mugadziri anofanira kutanga abviswa kubva kune mains.
Iyi programmer inogona kuiswa pamusoro kana kukwidziridzwa kune yakadzoreredzwa conduit bhokisi.
1) Bvisa iyo programmer kubva pakurongedzerwa kwayo. 2) Sarudza nzvimbo yekumisikidza yemugadziri:
- Isa iyo programmer 1.5 metres kumusoro kwepasi. -Dzivirira kuratidzwa kwakananga kuchiedza chezuva kana zvimwe zvinodziya / kutonhora masosi. 3) Shandisa philips screwdriver kusunungura screws yebackplate pasi pemugadziri. Iyo programmer inosimudzwa kumusoro kubva pasi uye inobviswa kubva kumashure.
(Ona mufananidzo 3 papeji 7)
4) Sveta iyo yekumashure pane yakadzoreredzwa conduit bhokisi kana zvakananga kumusoro. 5) Waya the backplate sezvakangoita wiring diagram iri papeji 6. 6) Gadzika programmer pabackplate uchiita shuwa kuti programmer pini nebackplate.
macontacts ari kugadzira ruzha, sundidzira mugadziri wepurogiramu achikwira kumusoro uye simbisa screws dzebackplate kubva pasi. (Ona mufananidzo wechitanhatu papeji 6)
8
R27V2
2 Zone Programmer Operating Instructions
Kukurumidza sumo kune yako R27V2 programmer:
Iyo R27V2 programmer ichashandiswa kudzora nzvimbo mbiri dzakapatsanurwa mukati mako yekudziya system yako.
Imwe neimwe zone inogona kushanda yakazvimirira uye kurongwa kuti ienderane nezvido zvako. Nzvimbo yega yega ine mapurogiramu anosvika matatu emazuva ese ekudziya anonzi P1, P2 uye P3. Ona Peji 13 kuti uwane mirayiridzo yekuti ungagadzirisa sei zvirongwa zvepurogiramu.
PaLCD skrini yemugadziri wako uchaona zvikamu zviviri zvakasiyana, chimwe chinomiririra imwe neimwe nzvimbo.
Mukati mezvikamu izvi iwe unogona kuona kuti iyo zone iri pari modhi ipi.
Kana iri muAUTO modhi, inozoratidza kana iyo zone ichitevera kurongwa kuti ibatiswe ON kana KUDZIMWA.
Nezve `Sarudzo yeModhi' ndapota ona peji 11 kuti uwane imwe tsananguro.
Kana iyo zone iri ON, iwe uchaona iyo tsvuku LED yeiyo zone mwenje kumusoro. Izvi zvinoratidza kuti simba riri kutumirwa kubva kumugadziri panzvimbo ino.
10
R27V2
Mode Selection
AUTO
Pane nzira ina dziripo pakusarudza.
AUTO Iyo zoni inoshanda kusvika kutatu `ON/OFF' nguva pazuva (P1,P2,P3).
ZUVA RESE Iyo zoni inoshanda imwe chete `ON/OFF' nguva pazuva. Izvi zvinoshanda kubva panguva yekutanga `ON' kusvika panguva yechitatu 'OFF'.
ON
Iyo zone iri ON zvachose.
DZIMA
Nzvimbo yacho AKADZIMWA zvachose.
Dzvanya Sarudza kuti uchinje pakati peAUTO, ZUVA RESE, ON & OFF.
Iyo yazvino modhi icharatidzwa pachiratidziri pasi peiyo zone chaiyo.
Iwo Sarudza anowanikwa pasi pebutiro rekutanga. Zone imwe neimwe ine yayo Sarudza.
EPH Controls Ltd.
11
Programming Modes
Uyu mugadziri ane anotevera maprogramming modes. 5/2 Zuva modhi Kuronga Muvhuro kusvika Chishanu sechivharo chimwe uye
Mugovera neSvondo sechivharo chechipiri. 2 Zuva modhi Kuronga ese mazuva manomwe ega. 7 Hour mode Kuronga mazuva ese 7 sebhuroka rimwe.
Factory Chirongwa Setting 5/2d
Mon-Fri Sat-Sun
Mazuva manomwe ese
Mazuva ese
P1 PASI 06:30 07:30
P1 PANE 06:30
P1 PANE 06:30
P1 KUBVA 08:30 10:00
P1 KUBVA 08:30
P1 KUBVA 08:30
5/2 Zuva P2 PA 12:00 12:00
7 Zuva P2 PA12:00
24 Awa P2 ON 12:00
P2 KUBVA 12:00 12:00
P2 KUBVA 12:00
P2 KUBVA 12:00
12
R27V2
P3 PASI 16:30 17:00
P3 PANE 16:30
P3 PANE 16:30
P3 KUBVA 22:30 23:00
P3 KUBVA 22:30
P3 KUBVA 22:30
Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi
Dzvanya PROG.
Chirongwa cheMuvhuro kusvika Chishanu cheZone1 chasarudzwa. Kuti uchinje programming yeZone 2, tinya yakakodzera Sarudza. Dzvanya uye kugadzirisa iyo P1 PANE nguva. Dzvanya uye kugadzirisa iyo P1 OFF nguva. Dzokorora maitiro aya kugadzirisa P2 uye P3 nguva.
Dzvanya OK . Dzvanya OK .
Chirongwa cheMugovera kusvika Svondo chasarudzwa.
Dzvanya uye kugadzirisa iyo P1 PANE nguva.
Dzvanya OK .
Dzvanya uye kugadzirisa iyo P1 OFF nguva.
Dzvanya OK .
Dzokorora maitiro aya kugadzirisa P2 uye P3 nguva.
Dzvanya MENU kuti udzokere kune zvakajairika.
Uchiri muchirongwa chekugadzira, kudzvanya Sarudza kuchasvetukira kuzuva rinotevera (block remazuva) pasina kuchinja chirongwa.
Cherechedza:
1. Kuti uchinje kubva pa5/2d kuenda ku7D kana 24H kuronga, tarisa kupeji 16, Menyu P01.
2. Kana iwe usingade kushandisa imwe kana akawanda ezvirongwa zvezuva nezuva zvino ingoisa nguva yekutanga uye nguva yekupedzisira kuti zvifanane. For exampuye, kana P2 yakagadzirirwa kutanga na 12: 00 uye kupera na 12: 00 mugadziri anongorega purogiramu iyi uye opfuurira kune imwe nguva yekuchinja.
EPH Controls Ltd.
13
Reviewkuisa Zvirongwa zvePurogiramu
Dzvanya PROG. Dzvanya OK kuti ufambe mukati menguva dzezuva rega rega (block of days). Dzvanya Sarudza kusvetukira kuzuva rinotevera (block yemazuva). Dzvanya MENU kuti udzokere kune zvakajairika. Iwe unofanirwa kudzvanya chaiyo Sarudza kuti udzokeview hurongwa hwenzvimbo iyoyo.
Boost Function
Imwe neimwe nzvimbo inogona kukwidziridzwa kwemaminetsi makumi matatu, 30, 1 kana maawa matatu apo zone iri muAUTO, ZUVA ROSE & OFF mode. Dzvanya Boost 2, 3, 1 kana 2 nguva, kuisa yaunoda BOOST nguva kuZone. Kana Boost ikadzvanywa pane kunonoka kwechipiri kusati kwaitwa apo `BOOST' ichapenya pachiratidziro, izvi zvinopa mushandisi nguva yekusarudza yaunoda BOOST nguva. Kukanzura BOOST, dzvanya iyo Boost yakafanana zvakare. Kana nguva yeBOOST yapera kana kukanzurwa, iyo Zone inodzokera kumodhi yaimboshanda pamberi peBOOST.
Cherechedza: A BOOST haigone kushandiswa uri muON kana Holiday Mode.
14
R27V2
Basa repamberi
Kana nzvimbo iri muAUTO kana ALLDAY modhi, iyo Advance basa inobvumira mushandisi kuunza zone kana nzvimbo kumberi kune inotevera nguva yekuchinja. Kana iyo zone yave panguva yekuve OFF uye ADV yakatsikirirwa, iyo zone ichabatidzwa ON kusvika pakupera kwenguva inotevera yekuchinja. Kana iyo zone yave panguva yekuve ON uye ADV yakatsikirirwa, iyo zone ichadzimwa kusvika panotanga nguva inotevera yekuchinja. Dzvanya ADV. Zone1 uye Zone 2 ichatanga kupenya. Dzvanya yakakodzera Sarudza. Iyo zone icharatidza `ADVANCE ON' kana `ADVANCE OFF' kusvika pakupera kwenguva inotevera yekuchinja. Zone 1 inomira kupenya uye kupinda Advance mode. Zone 2 icharamba ichipenya. Dzokorora maitiro aya neZone 2 kana zvichidikanwa.
Dzvanya OK . Kukanzura ADVANCE, tinya yakakodzera Sarudza . Kana nguva yeADVANCE yapera kana kukanzurwa, nzvimbo yacho inodzokera kumodhi yaimboshanda pamberi peADVANCE.
EPH Controls Ltd.
15
Menu Basa
Iyi menyu inobvumira mushandisi kugadzirisa mamwe mabasa. Kuti uwane menyu, dzvanya MENU .
P01 Kuisa Zuva, Nguva uye Chirongwa cheModhi DST ON
Dzvanya MENU , `P01 tInE' ichaonekwa pachiratidziri. Dzvanya OK , gore richatanga kupenya. Dhinda uye kugadzirisa gore. Dzvanya uye kugadzirisa mwedzi. Dzvanya uye kugadzirisa zuva. Dzvanya uye kugadzirisa awa. Dzvanya uye kugadzirisa miniti. Dzvanya uye kugadzirisa kubva pa5/2d kuenda ku7d kana 24h modhi. Dzvanya uye kubatidza DST (Day Light Saving time) Vhura kana Kudzima. Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.
Cherechedza: Ndokumbira utarise peji 12 kune tsananguro dzeProgramming Modes.
Dzvanya OK . Dzvanya OK . Dzvanya OK . Dzvanya OK . Dzvanya OK . Dzvanya OK .
16
R27V2
P02 Holiday Mode
Iyi menyu inobvumira mushandisi kudzima yavo yekudziya system nekutsanangura zuva rekutanga uye rekupedzisira.
Dzvanya MENU , `P01' ichaonekwa pachiratidziri.
Dzvanya kusvika `P02 HOL' ichionekwa pachiratidziri.
Dzvanya OK , `HOLIDAY FROM', zuva uye nguva zvichaonekwa pachiratidziri. Gore richatanga kupenya.
Dhinda uye kugadzirisa gore.
Dzvanya OK .
Dzvanya uye kugadzirisa mwedzi.
Dzvanya OK .
Dzvanya uye kugadzirisa zuva.
Dzvanya OK .
Dzvanya uye kugadzirisa awa.
Dzvanya OK .
`HOLIDAY TO' uye zuva nenguva zvichaonekwa pachiratidziri. Gore richatanga kupenya.
Dhinda uye kugadzirisa gore.
Dzvanya OK .
Dzvanya uye kugadzirisa mwedzi.
Dzvanya OK .
Dzvanya uye kugadzirisa zuva.
Dzvanya OK .
Dzvanya uye kugadzirisa awa. Iyo programmer zvino ichadzimwa panguva iyi yakasarudzwa.
Dzvanya OK .
Kukanzura HOLIDAY, dzvanya OK . Iyo programmer ichadzokera kune yakajairika kushanda kana zororo rapera kana kukanzurwa.
EPH Controls Ltd.
17
Menu Function yakaenderera mberi
P03 Frost Dziviriro YADZIMWA
Iyi menyu inobvumira mushandisi kumutsa kudzivirira kwechando pakati pe5°C ne20°C.
Kudzivirirwa kwechando kunogadzikwa ku OFF. Dzvanya MENU , `P01' ichaonekwa pachiratidziri. Dzvanya kusvika `P03 FrOST' yaonekwa pachiratidziri. Dzvanya OK , `OFF' ichaonekwa pachiratidziri.
Dzvanya kuti usarudze `ON'. `5°C' ichapenya pachiratidziri.
Dzvanya OK .
Dzvanya uye kusarudza tembiricha yako yaunoda kudzivirira chando.
Dzvanya OK .
Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.
Chiratidzo cheFrost chicharatidza pachiratidziri kana mushandisi akachimisa mumenyu.
Kana tembiricha yekamuri yemukati ikadonha pasi peinodikanwa tembiricha yechando, nzvimbo dzese dzemugadziri dzinoita uye chiratidzo chechando chinopenya kusvika tembiricha yekudzivirira chando yawanikwa.
18
R27V2
P04 Zone Title
Iyi menyu inobvumira mushandisi kusarudza mazita akasiyana enzvimbo yega yega. Zvisarudzo ndezvi:
DEFAULT OPTIONS MVURA INOPITSA KUPIYA
DZORERA ZVINODA ZONE 1 ZONE 2
Dzvanya MENU , `P01' ichaonekwa pachiratidziri. Dzvanya kusvika `P04' yaonekwa pachiratidziri. Dzvanya OK , `MVURA INOPISHA' inopenya pachiratidziri. Dzvanya kuti uchinje kubva pa'MVURA INOPISA' kuenda ku'ZONE 1′. Dzvanya OK . `KUSVIRA' kuchapenya pachiratidziri. Dzvanya kuti uchinje kubva pa `KUSVIRA' kuenda ku `ZONE 2′. Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.
EPH Controls Ltd.
19
Menyu Basa rakaenderera mberi P05 PIN
Iyi menyu inobvumira mushandisi kuisa kiyi yePIN pamugadziri wepurogiramu. Kukiya kwePIN kunoderedza kushanda kwemugadziri. Gadzirisa PIN
Dzvanya MENU , `P01' ichaonekwa pachiratidziri. Dzvanya kusvika `P05 PIN' yaonekwa pachiratidziri. Dzvanya OK, `OFF' ichaonekwa pachiratidziri. Dzvanya kuti uchinje kubva pa OFF kuenda pa ON. Dzvanya OK . `0000′ ichapenya pachiratidziri. Dzvanya uye kuseta kukosha kubva pa0 kusvika 9 kune yekutanga digit. Dzvanya OK kuti uende kune inotevera PIN digit. Kana nhamba yekupedzisira yePIN yaiswa, tinya OK. Verify inoratidzwa ne `0000′. Dzvanya uye kuseta kukosha kubva pa0 kusvika 9 kune yekutanga digit. Dzvanya OK kuti uende kune inotevera PIN digit. Kana nhamba yekupedzisira yePIN yaiswa, tinya OK. Iyo PIN ikozvino yakasimbiswa, uye PIN yekiyi yakavhurwa.
Kana iyo yekusimbisa PIN ikaiswa zvisizvo mushandisi anodzoserwa kumenyu. Kana iyo PIN yekuvhara ichishanda iyo Lock chiratidzo chinopenya sekondi yega yega pachiratidziri. Kana iyo programmer iPIN yakakiyiwa, kudzvanya menyu kunoendesa mushandisi kuPIN yekuvhura skrini. Ongorora: Kana iyo PIN yekuvhara yakagoneswa, BOOST nguva inoderedzwa kusvika makumi matatu maminetsi uye 30 awa nguva. Kana iyo PIN yekuvhara yakagoneswa, Mode Sarudzo inoderedzwa kuita Auto uye OFF.
20
R27V2
Kuti uvhure PIN
Dzvanya MENU, `UNLOCK' ichaonekwa pachiratidziri. `0000′ ichapenya pachiratidziri.
Dzvanya uye kuseta kukosha kubva pa0 kusvika 9 kune yekutanga digit.
Dzvanya OK kuti uende kune inotevera PIN digit.
Kana iyo yekupedzisira nhamba yePIN yaiswa.
Dzvanya OK .
Iyo PIN ikozvino yavhurwa.
Kana PIN yakavhurwa pane programmer, inozozvimisikidza zvakare kana pasina bhatani rakadzvanywa kwemaminetsi maviri.
Kudzima PIN
Kana PIN yakavhurwa (ona mirairo iri pamusoro)
Dzvanya MENU , `P01' ichaonekwa pachiratidziri.
Dzvanya kusvika `P05 PIN' yaonekwa pachiratidziri.
Dzvanya OK, `ON' ichaonekwa pachiratidziri.
Dzvanya kana kusarudza `OFF'.
Dzvanya OK .
`0000′ ichapenya pachiratidziri. Isa PIN. Iyo PIN ikozvino yakadzimwa.
Dzvanya OK .
Dzvanya MENU kuti udzokere kune zvakajairika kana kuti inozobuda yega mushure memasekondi makumi maviri.
EPH Controls Ltd.
21
Copy Basa
Copy basa rinogona kushandiswa chete kana iyo 7d modhi yasarudzwa. (Ona peji 16 kuti usarudze 7d modhi) Dzvanya PROG kuronga nguva dzeON uye OFF dzezuva revhiki raunoda kukopa. Usadzvanya OK pane P3 OFF nguva, siya iyi nguva ichipenya. Dzvanya ADV, `COPY' ichaonekwa pachiratidziri, nezuva rinotevera revhiki richipenya. Kuti uwedzere hurongwa hwaunoda kusvika nhasi dzvanya . Kudarikira zuva iri dzvanya . Dzvanya OK kana chirongwa chashandiswa kumazuva aunoda. Ita shuwa kuti iyo zone iri mu Auto mode kuti iyi hurongwa ishande zvinoenderana. Dzokorora maitiro aya eZone 2 kana zvichidikanwa.
Ongorora: Iwe haugone kukopa masheti kubva kune imwe nzvimbo kuenda kune imwe, Eg Kukopa Zone 1 hurongwa kuZone 2 hazvigoneke.
22
R27V2
Backlight Mode Sarudzo ON
Pane 3 backlight marongero aripo ekusarudza:
AUTO Backlight inogara yakabatidzwa kwemasekonzi gumi kana chero bhatani rikadzvanywa.
ON
Backlight inobatidzwa zvachose.
DZIMA
Backlight iri Off zvachose.
Kugadzirisa backlight dzvanya uye bata OK kwemasekonzi gumi. `Otomatiki' inoonekwa pachiratidziri. Dzvanya kana kushandura modhi pakati peAuto, On uye Off. Dzvanya OK kuti usimbise sarudzo uye kudzokera kune yakajairika kushanda.
EPH Controls Ltd.
23
Kukiya Keypad
Kukiya mugadziri, dzvanya uye ubate uye pamwe chete kwemasekonzi gumi. ichaonekwa pachiratidziri. Mabhatani ava kuremara.
Kuti uvhure mugadziri, dzvanya uye ubate uye kwemasekonzi gumi. ichanyangarika kubva pahwindo. Mabhatani ava kugoneswa.
Resetting the Programmer
Kugadzirisa zvakare mugadziri kune zvigadziriso zvefekitori: Dzvanya MENU . `P01' ichaonekwa pachiratidziri. Dzvanya kusvika `P06 reSET' yaonekwa pachiratidziri. Dzvanya OK kuti usarudze. `nO' ichatanga kupenya. Dzvanya , kuchinja kubva ku `nO' kuenda ku `YES'. Dzvanya OK kuti usimbise.
Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero. Nguva uye zuva hazvizogadzirwe patsva.
24
R27V2
Master Reset
Kuti ugone kuseta zvakare mugadziri kune zvigadziriso zvefekitori, tsvaga bhatani reseta bhatani kurudyi-kurudyi pasi pemugadziri. (ona peji 5) Dzvanya bhatani reReset Master worisunungura. Iyo skrini ichaenda isina chinhu uye reboot. Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero.
Service Interval OFF
Iyo nguva yebasa inopa mugadziri kugona kuisa yegore countdown timer pane programmer. Kana iyo Service Interval ikamiswa `SERv' ichaonekwa pachiratidziri iyo inozivisa mushandisi kuti yavo yegore boiler sevhisi inofanirwa.
Kuti uwane ruzivo rwekugonesa kana kudzima iyo Service Interval, ndapota taura nevatengi.
EPH Controls Ltd.
25
EPH Inodzora IE
technical@ephcontrols.com www.ephcontrols.com/contact-us T +353 21 471 8440
EPH Inotonga UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk/contact-us T +44 1933 322 072
©2024 EPH Controls Ltd. 2024-01-04_R27-V2_DS_PK
Zvinyorwa / Zvishandiso
 |
EPH INODZORA R27 V2 Zone Programmer [pdf] Installation Guide R27 V2 Zone Programmer, R27 V2, Zone Programmer, Programmer |