Futaba T4PM Software Update Method

Product Information

Zvinotsanangurwa

• Model: 1M23Z09912
• Product Name: T4PM Software Update Method

4PM Software Update Method
Whenever improvements and new functions are available, the software of your T4PM radio transmitter can be updated easily online free of charge. The updated software file zvicharatidzwa kwatiri website. Unogona kuidhawunirodha uye woita kopi pane yako microSD kadhi. Pazasi pane maitiro ekugadzirisa software.

Procedure for the Software Update

Yambiro: Before you update the software, the battery that is connected to the T4PM should be fully charged.

Cherechedza: During the software update, the model data that is stored in the T4PM should be kept without any change. (NOT erased and NOT changed.) However, for your safety, making a backup of your model data before the software update is highly recommended.

1. Dhaunirodha zip file yedata rekuvandudza kubva kune yedu website.
2. Bvisa zip file pakombuta yako.
3. Iyo "FUTABA" folda ichagadzirwa pakombuta yako.
4. Copy the “FUTABA” folder onto your microSD card.
5. Insert the microSD card with “FUTABA” folder that contained the update software into the SD card slot on your T4PM radio transmitter.
6. Turn on the transmitter power while pressing down the “END” button. The update screen appears on the LCD display of your T4PM and the software update is started.
7. When the software update is completed, “Completed” message is shown on the LCD display of your T4PM.
8. Turn off the power switch of your T4PM and remove the microSD card from the card slot.
   microSD card (sold separately)
   (Commercial product) SD standard and SDHC standard microSD cards SD/SDHC format. Maximum size 32MB. SDXC format is not supported.

Software Version Updates

Fixed Gyro Link Function (V5.61)
Gyro link function: Changes to LMT A/B settings and NT-OFFSET setting methods. The operation method when using T-FHSS SR mode has been adjusted to match that of other models such as the T10PX. If you have changed the LMT A/B settings or NT-OFFSET settings, move the cursor to [WRITE] and press the (JOG) button to perform the write operation.

Compatible with HPS-CD701 / S-CD400 (V5.60)
Added support to change the SR mode of HPS-CD701 and S-CD400. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with S-C401 (V5.50)
Added support to change the SR mode of S-C401. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with BLS-CM600 / S-C400 / S-C300 (V5.40)
Added support to change the SR mode of BLS-CM600/S-C400/S-C300. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with HPS-CT501 (V5.30)
Added support to change the SR mode of HPS-CT501. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with HPS-CT702 / HPS-CD700 (V5.20)
Added support to change the SR mode of HPS-CT702 and HPS-CD700. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with HPS-CB701 (V5.10)
Added support to change SR mode of HPS-CB701. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Compatible with HPS-CT701 (V5.04)
Added support to change SR mode of HPS-CT701. * UR mode is not supported. If the servo is set to UR mode, change it to normal mode or SR mode before using it.

Radio Communication (V5.03)
Kuvandudzwa kwakaitwa kugonesa kurukurirano yakatsiga zvikuru kunyange munzvimbo umo ma<em>transmitters mazhinji ari kubudisa masaisai eredhiyo munzvimbo imwe cheteyo.

Gyro Link
Yakachinja kuseta kweiyo Gyro Link muganho kukosha kubva pa10 kuenda ku130.

Software Fix (V5.01)
Yakagadzirisa iyo timer basa.

Update Function / Roll Out Chart and Gear Ratio Chart (V5.0)
Sarudzo yemhando yega yega yakawedzerwa kutsigira Kyosho Mini-Z.

Setting range after update: Pinion gear: 5-75 / Spar gear: 25-130 / Tire diameter: 20.0-65.0

Zvimwe
Yakawedzera tsigiro yekuchinja SR modhi yeHPS-CB500 / HPS-CT500.

Additional Function / Gyro Link (V4.0)

Iyo Gyro Link ibasa rinokutendera kuti uise maparamita emota gyro isina waya kubva kune inotumira.

• A gyro compatible with the wireless setting: GYD550 (As of April 2020)
• Up to five presets can be switched while driving. (Gyro data switching function)
• Iyo S.BUS servo data inogona kusetwa isina waya kubva kune transmitter kuburikidza ne gyro.

* A receiver compatible with the wireless setting function is required. (As of April 2020, R334SBS / R334SBS-E is compatible with wireless setting. Please update the previous receiver to version 4.0 or later)

* While using Gyro Link wireless (SBUS connection) SBUS servo adjustment will not function.

To be able to control gyro gain, etc. from the transmitter, it is necessary to enable the gyro mixing function of the transmitter.

Using the Gyro Link Function

Kugadzirira
Batanidza inogamuchira uye gyro zvinoenderana nedhiyagiramu yekubatanidza pazasi.

* The connection diagram is a reference diagram for selecting the gyro link connection method. Please read the gyro instructions for details or cautions.

1. Batidza switch yemagetsi yetransmitter kuratidza iyo Gyro Link skrini. Batidza switch yemagetsi inogamuchira.
2. (Gyro read) Execute this function to read the data currently set at the gyro. Select the setting item “LINK” by moving the (JOG) button up or down. Select the connection type by (+) or (-) button, and press the (JOG) button. A beep sounds and the gyro data is read.
3. (Writing to gyro) Execute this function to write the setting data to the gyro. Select the setting item “WRITE” by moving the (JOG) button up or down, and press the (JOG) button. A beep sounds and the gyro data is written.
   • Kana "COM-ERROR" ichibwaira pachiratidziri, kutaurirana negyro hakusi kuitwa zvakajairika. Tarisa hukama pakati peanogamuchira, gyro, uye bhatiri, batidza simba remupepeti uye mugamuchiri, uye dzokorora WRITE.
4. (Initialization) This function writes the gyro setting data set at the factory to the connected gyro. Select the setting item “RESET” by moving the (JOG) button up or down, and press the (JOG) button. A beep sounds and the gyro data is initialization.
   • If “COM-ERROR” blinks on the screen, communication with the gyro is not being performed normally. Check the connection between the receiver, gyro, and battery, turn on the power of the transmitter and receiver, and repeat RE- SET.

Data Settings

Sarudza chinhu chekuseta nekufambisa (JOG) bhatani kumusoro kana pasi. Seta kukosha ne (+) uye (-) bhatani.

Example: (BASIC SET screen)

Setup Item Selection: Select by the (JOG) button. The item indicated by the reverse displayed cursor is selected.

Set Button: Use the (+) and (-) buttons to make adjustments. Return to the initial value by pressing the (+) and (-) buttons simultaneously (approx. 1 sec).

Seta bhatani

• Shandisa (+) uye (-) mabhatani kugadzirisa.
• Dzokera kune yekutanga kukosha nekudzvanya (+) uye (-) mabhatani panguva imwe chete (approx. 1 sec).

Basic Set

* In the T-FHSS SR mode, the servo position will not adjust until “WRITE”, even if the “LMT” and “NT-OFFSET” functions are adjusted with (+) and (-) buttons.

GYRO DATA
Iyo data inogona kusetwa yakazvimirira mune yega yega gyro oparesheni modhi (AVCS / NORMAL).

Additional / Acuvance Xarvis / XarvisXX Compatible (MC (ESC) Link)

The MC (ESC) Link function is now compatible with Acuvance ESC Xarvis and XarvisXX.

* Please contact Acuvance for details of Xarvis / XarvisXX functions.

• When using the MC970CR or Acuvance Xarvis, select “MC970CR”, and when using Acuvance XarvisXX, select “Xar- visXX”
• For Futaba ESC MC960CR, MC950CR, MC851C, MC602C, MC402CR, etc., please choose Other. * MC970CR is available only in the Japanese market. (As of April 2020)

Additional Function / Start (V3.0)
Kana iyo track ichitsvedza uye iwe ukatanga kumhanyisa nekusundidzira chinokonzeresa kuti chiite throttle yakazara, mavhiri emota anotenderera uye mota haichamhanyire zvakanaka. Kana iyo Yekutanga basa yakagadziriswa, kungoshandisa iyo throttle trigger zvishoma nezvishoma inokonzera throttle servo kuti ichinje kubva panzvimbo yakagadzika throttle kusvika panzvimbo yakagadziriswa kuitira kuti matai arege kurasikirwa nekubata uye motokari inokurumidza kukurumidza.

Operation

• Kana iyo throttle trigger ichiendeswa kune preset chinzvimbo (TRIGGER POINT), iyo throttle servo inoenda kune preset chinzvimbo.
• Kana iyo throttle trigger ichishandiswa zvishoma nezvishoma kuitira kuti mavhiri arege kutenderera, motokari inomhanya ichienda kune yakarongwa.
• This function is effective only for the first throttle trigger operation at starting. This function has to be activated before every start.
• Kana iyo throttle trigger ikadzoserwa zvishoma, iyo Yekutanga basa inodzima uye iyo set inodzokera kune yakajairwa throttle trigger oparesheni.

Traction control basa kugadzirisa

Changed Function / Model Copy

• The new model copy function allows you to copy the model data of the transmitter to a microSD card. The models copied in the microSD card cannot be used by directly calling from the card. Please copy it to the T4PM main unit when using it.
• Kana iyo data yemuenzaniso yeimwe transmitter yakachengetwa kune microSD kadhi, iyo data yemuenzaniso haina kuratidzwa mune iyi runyorwa.
• There is no limit to the number of model data on the microSD card, but it differs depending on the capacity by size of the card. However, the model data displayed in the list is a maximum of 100 models. In addition, there is no rule in the display order.
• Paunenge uchiratidzira menyu yekukopa kana uchiita basa rekukopa, buzzer ine nzwi rakafanana neyekuvhiya kiyi inogona kunzwika ichienderera, asi uku hakusi kushata.

Using the Model Copy Function

1. (Select a Mode) In “MODE”, select the copy source and copy destination devices. Select the setting item “MODE” by moving the (JOG) button up or down. Use the (+) or (-) button and set the copy source and copy destination devices.
2. (Copy Source Model Selection) Select the setting item “FROM” by moving the (JOG) button up or down, and press the (JOG) button to display a list of model numbers.Sarudza iyo yekukopa modhi ine (JOG) bhatani kumusoro / pasi kana kuruboshwe / kurudyi, uye dzvanya bhatani re (JOG). Dzokera kukopi skrini.
3. (Copy destination model selection) Select the setting item “TO” by moving the (JOG) button up or down, and press the (JOG) button to display a list of model numbers. -When the destination is “TX”, a list of 1 to 40 models is displayed. -When the copy destination is “SD”, the list is not displayed even if the (JOG) button is pressed for additional copying to the SD card. Select the copy destination model with the (JOG) button up / down or left / right operation, and press the (JOG) button. Return to the copy screen.
4. (Model copy execution) Select the setting item “EXEC” by moving the (JOG) button up or down, and press the (JOG) button. A beeping sound is generated and the copying is complete. -Copying is complete when “COMPLETE!” is displayed on the screen.
5. Kana wapedza, dzokera kuMENU sikirini nekudzvanya (END) bhatani.

Kuwedzera basa / Model kudzima (Yakachengetedzwa pane SD kadhi)

Iri basa rinobvisa modhi data yakachengetwa pane SD kadhi.

Maitiro ekudzima modhi data mune SD kadhi

1. (Select model to delete) Select the model to delete by moving the (JOG) button up or down. -When the number of models that do not fit on one page is saved, arrows are displayed on the left and right of the page number on the screen. Operate the (JOG) button left or right to move the peji.Sarudza button – Select with the (JOG) button.
2. (Perform delete) After selecting the model to delete, press the (JOG) button.The mes- sage “DELETE ARE YOU SURE?” is displayed. When you press the (JOG) button, a beep sounds and the model data is deleted.
   Kuuraya button – Pressing the (JOG) button.
3. Kana wapedza kuseta, dzokera kuMENU skrini nekudzvanya bhatani re (END).

Other Added support to change SR mode of HPS-CT700.

Kuwedzera basa / Throttle Speed ​​Return Setting
In the speed function, a setting has been added for the “return” side when returning from the throttle high side to the neutral direction. The setting method is the same as the lower side of the screen. “return” side of steering speed. Also, a servo operation monitor has been added to the lower side of the screen.

Yambiro
Setting the speed function in the return direction slows the de- celeration of the car body, so please be careful to set it carefully.

Kuwedzera basa / Iyo 3/4 Brake Channel Kuwedzera
Kana iyo "Brake kusanganisa" basa ririkusetwa, iyo 3rd uye 4th chiteshi brake side kukwirisa inozogadziriswa.

Kuwedzera basa / Tangi Kusanganisa
This function is intended for vehicles such as tanks and can be used for the pivotal turn, or the ultra-pivot- al brake turn, by steering and throttle operation.

Tangi kusanganisa kugadzirisa

When steering and trigger are operated at the same time. If you manipulate the trigger to the high side and operate the steering wheel to the right, the tank will turn right at the rate of “FWRD”, “RIGHT”. If you manipulate the trigger to the high side and operate the steering wheel to the left, the tank turns to the left at the rate of “FWRD”, “LEFT”. Operating the steering wheel while operating the trigger to the brake side will operate the same as the forward side in the reverse direction.

Kuwedzera basa / Kudhonza

Trigger operation with cornering on a slippery road surface is hard to get traction and smooth cornering cannot be done. By intermittently pulsing the throttle, you can smoothly navigate and travel on topological lines. Also, with a drift car, by intermittently operating the motor in the high point direction, a pseudo re- verberator engine sound can be reproduced.

Operation

• Munguva yekushanda kwe throttle, iyo throttle servo inoshandiswa nguva nenguva ichienda mberi.
• Iwe unogona kuseta huwandu hwekudzoka kudivi rinononoka, huwandu hwekunonoka, kukurumidza kwekupomba, nzvimbo yekushandisa, uye chiyero chebasa chekupomba.
• Iwe unogona kusarudza chiito padivi rinononoka padhuze nekwakarerekera uye chiito pane yakakwira point side.

Chinja marongero
Shandisa SW1 kana SW2 kuti uchinje iyo inodhonza control function ON/OFF.

Dial / Trim Setting
The throttle return amount, delay amount and cycle speed can be controlled with digital trim DT to DT5 or digital dial DL1 etc. with the dial select function.

Nezve Fail Safe Unit
Iko kushandiswa kweiyo Futaba fail safe unit (FSU) yakafanana nerondedzero yepeji yeiyo TH ABS basa.

• MODE: Function ON/OFF
  Traction control functions ON/OFF setting. When us- ing the Traction control function, set to “ON”.
•  RETN: Throttle return
  Set the ratio at which the servo returns to the slow side with respect to the trigger operation. If set to 0%, the traction control function will not work. At 50%, it returns to the neutral position at 50% (half), 100% of the trigger operation amount.
• DELY: Kunonoka
  Set the delay from when the throttle is operated until when the traction control operation starts. When set to 0%, the traction control function works without delay. At 50%, the traction control function works approximately 0.5 second later, and the traction control function works about 1.0 second later at 100%.
• CYCL: Cycle speed Sets the pulse speed (cycle speed). The smaller the set value, the faster the pulse cycle.
• BASA: Duty ratio Set the ratio of the time to operate to the high side and the time to operate to the slow side in the pumping operation. The ratio can be set to HIGH, MID or LOW.
• TG.P: Trigger point / TYPE: Operating range In the throttle operation, set the position of the trigger at which traction control starts to work. Normal / Reverse, reverse the throttle operation range where the traction control operates, with the trigger point as the boundary.

Traction control basa kugadzirisa

7 When finished with the setting, return to the MENU screen by pressing the (END) button.

Kuwedzera basa / Reset iyo sensor slot nhamba
Iri basa ndere kuseta zvakare iyo sensor slot nhamba kana uchishandisa sensor ine slot nhamba yakashandurwa neimwe transmitter. Batanidza sensor sezvakaratidzwa uye rejista zvinoenderana neinotevera maitiro.

Sensor batanidza

Maitiro ekugadzirisa zvakare sensor slot nhamba

1. (Execute reset) Press the (JOG) button for about 1 second. -“COMPLETE!” blinks on the screen and reset sensor slot number. – If “COM-ERROR” blinks on the screen, communication with the sensor is not being performed normally. Check the T4PM and sensor connection and the battery connection to sensor and repeat RESET.
2. Kana wapedza kuseta, dzokera kuMENU skrini nekudzvanya bhatani re (END).

Kuwedzera basa / Rondedzera Chati
This function is designed for pan cars. The roll out chart can be calculated from input values for the num- ber of teeth of the spur gear and pinion gear, and the tire diameter, and displayed as a table.

Kushandiswa kweRoll out chart function

1. (Setting of step of the tire diameter input) Select the setting item “STEP” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the step of input numerical value of tire diameter amount. -The step amount can be set in the range of 0.1 mm to 1.0 mm.
2. Setting of number of teeth of spur gear) Select the setting item “SPUR” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the spur gear. The roll out is then calculated, and the list is updated.
3. (Setting of number of teeth of pinion gear) Select the setting item “PINION” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the pinon gear. The roll out is then calculated, and the list is updated.
4. (Setting of tire diameter) Select the setting item “DIAMT” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the tire diameter. The roll out is then calculated, and the list is updated.
5. Kana wapedza kuseta, dzokera kuMENU skrini nekudzvanya bhatani re (END).

Kuwedzera basa / Gear Ratio Chati
The Gear Ratio Chart can be calculated from input values for the number of teeth of the spur gear and inion gear, and secondary gear ratio, and displayed as a table.

Kushandiswa kweGear ratio chart function

1. Setting of number of teeth of pinion gear) Select the setting item “PINION” by moving the (JOG) button up or down. Use the (+) and (- buttons to set the pinon gear. The roll out is then calculated, and the list is updated.
2. (Setting of number of teeth of spur gear) Select the setting item “SPUR” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the spur gear. The roll out is then calculated, and the list is updated.
3. (Setting of number of secondary gear ratio) Select the setting item “2nd RATIO” by moving the (JOG) button up or down. Use the (+) and (-) buttons to set the 2nd gear ratio. The roll out is then calculated, and the list is updated.
4. Kana wapedza kuseta, dzokera kuMENU skrini nekudzvanya bhatani re (END).

Mibvunzo Inowanzo bvunzwa

How often should I update the software on my T4PM device?

It is recommended to check for software updates regularly and update your device whenever a new version is available to ensure optimal performance and security.

Zvinyorwa / Zvishandiso

Futaba T4PM Software Update Method [pdf] Mirayiridzo T4PM Software Update Method, T4PM, Software Update Method, Update Method, Method

References

• User Manual