itsnsor N1040 Temperature Sensor Controller

CHENJERERO CHEKUCHENGETEKA

Zviratidzo zviri pazasi zvinoshandiswa pamidziyo uye mugwaro rose rino kukwevera kutarisa kwemushandisi kune yakakosha ruzivo rwekushandisa uye kuchengetedza.

CHENJERERO:Verenga bhuku racho zvakakwana usati waisa uye kushandisa michina.

CHENJERERO KANA NJODZI: Electrical shock ngozi

Yese mirairo ine chekuita nekuchengetedza inoonekwa mubhuku rekushandisa inofanirwa kucherechedzwa kuve nechokwadi chekuchengetedzwa kwemunhu uye kudzivirira kukuvadzwa kune chingave chiridzwa kana system. Kana chiridzwa chacho chikashandiswa nenzira isina kutaurwa nemugadziri, kuchengetedzwa kunopiwa nemidziyo kunogona kukanganisa.

INSTALLATION / CONNECTIONS

Iyo controller inofanirwa kusungirirwa pane pani, ichitevera kutevedzana kwematanho anotsanangurwa pazasi:

• Gadzirira mapaneru akachekwa-kunze zvinoenderana Nekutsanangurwa;
• Bvisa iyo inokwirisa clamps kubva kumutongi;
• Isai controller mupaneru yekucheka-kunze;
• Svetera iyo inokwirisa clamp kubva kumashure kusvika pakubata kwakasimba pane panel.

KUKUNGAMIRIRA KWEMAGETSI
Mufananidzo 01 pazasi inoratidza materminal emagetsi emutongi:

ZVINOKUDZIDZWA ZVOKUGADZIRA 

• Kubatanidzwa kwese kwemagetsi kunogadzirwa kune screw terminals kumashure kwemutongi.
• Kuderedza kunhonga-up kwemagetsi emagetsi, iyo yakaderera voltage DC yekubatanidza uye iyo sensor yekupinza wiring inofanirwa kuendeswa kure neakakwira-azvino magetsi conductor.
• Kana izvi zvisingaite, shandisa tambo dzakavharidzirwa. Kazhinji, chengetedza kureba kwetambo kusvika kushoma. Zvese zviridzwa zvemagetsi zvinofanirwa kufambiswa neakachena mains anopihwa, akakodzera kune chiridzwa.
• Zvinokurudzirwa kushandisa RC'S FILTERS (ruzha suppressor) kune contactor coils, solenoids, etc. Mune chero application, zvakakosha kufunga zvinogona kuitika kana chero chikamu chehurongwa chikatadza. Iyo controller maficha ega haagone kuvimbisa kuchengetedzwa kwakazara.

FEATURES

INPUT TYPE SELECTION

Tafura 01 inoratidza marudzi e sensor anogamuchirwa uye macode avo uye mazinga. Svika iyo parameter TYPE mukutenderera kweINPUT kuti usarudze iyo sensor yakakodzera.

ZVINOBUDA
Iyo controller inopa maviri, matatu kana mana ekubuda chiteshi, zvichienderana neakatakura sarudzo maficha. Iwo anobuda chiteshi anogadziriswa nemushandisi seKudzora Kubuda, Alarm 1 Output, Alarm 2 Output, Alarm 1 OR Alarm 2 Output uye LBD (Loop Break Detect) Output.

OUT1 - Pulse mhando kubuda kwemagetsi voltage. 5 Vdc / 50 mA max.
Inowanikwa pamaterminals 4 ne5

OUT2 – Relay SPST-NA. Inowanikwa kumaterminals 6 ne7.

OUT3 – Relay SPST-NA. Inowanikwa kumaterminals 13 ne14.

OUT4 - Relay SPDT, inowanikwa kumaterminals 10, 11 uye 12.

KUDZORA KUBUDZWA
Nzira yekutonga inogona kuva ON / OFF (apo PB = 0.0) kana PID. Iyo PID paramita inogona kusarudzwa otomatiki inogonesa iyo auto-tuning basa (ATvN).

ALARM OUTPUT
Iyo controller ine 2 maalarm anogona kutungamirwa (kupihwa) kune chero nzira inobuda. Mabasa ealarm anotsanangurwa muTable 02.

Cherechedza: Alarm mabasa paTable 02 anoshandawo kune Alarm 2 (SPA2).

Chiziviso chakakosha: Maalarm akagadziridzwa ne ki, dif uye difk mabasa zvakare anokonzeresa kuburitsa kwavo kwakabatana kana chikanganiso che sensor chikaonekwa uye chichisainwa nemutongi. A relay kubuda, kune example, yakagadzirirwa kuita seAlarm Yepamusoro (ki), ichashanda kana kukosha kweSPAL kwapfuudzwa uyezve kana sensor yakabatana neinopinza yekudzora yaputswa.

PAKUTANGA KUBVISWA KWE ALARM

Iyo yekutanga yekuvharira sarudzo inotadzisa alarm kuti isazivikanwe kana alarm mamiriro aripo kana controller atanga kupihwa simba. Iyo alarm inozogoneswa chete mushure mekuitika kweiyo isiri-alarm mamiriro. Kuvhara kwekutanga kunobatsira, kune example, kana imwe yearamu yakagadziridzwa seyakaderera kukosha kwearamu, zvichikonzera activation yearamu munguva pfupi yekutanga-maitiro, chiitiko chingave chisingadikanwi. Iko kuvharika kwekutanga kwakavharwa kune sensor break alarm function ierr (Vhura sensor).

KUKOSHA KUNOBUDA NESENSOR FAILURE
Basa rinoisa kuburitsa kwekutonga munzvimbo yakachengeteka yemaitiro kana ichinge yaonekwa chikanganiso mukupinza sensor. Nekukanganisa kunoonekwa mu sensor, mutongi anosarudza muzanatage kukosha inotsanangurwa muparameter 1E.ov yekutonga kuburitsa. Mutongi acharamba ari mumamiriro ezvinhu aya kusvikira kutadza kwe sensor kwapera. 1E.ov tsika dzinongori 0 uye 100% kana iri muON/OFF control mode. YePID yekudzora maitiro, chero kukosha muhuwandu kubva 0 kusvika 100% inogamuchirwa.

LBD BASA - LOOP BREAK KUONA
Iyo LBD.t parameter inotsanangura nguva yenguva, mumaminitsi, mukati meiyo PV inotarisirwa kuita kune yekudzora kubuda chiratidzo. Kana iyo PV isingabatanidzi zvakanaka mukati menguva yenguva yakagadziriswa, mutongi anoisa chiratidzo mukuratidzira kwayo kuitika kwechiitiko cheLBD, chinoratidza matambudziko mukutonga loop.
Chiitiko cheLBD chinogona zvakare kutumirwa kune imwe yematanho ekubuda emutongi. Kuti uite izvi, ingo gadzirisa yaunoda inobuda chiteshi neiyo LDB basa iro, muchiitiko chechiitiko ichi, chinotangwa. Iri basa rakavharwa nemutengo we0 (zero). Iri basa rinobvumira mushandisi kuona matambudziko mukumisikidza, senge akaremara actuators, kutadza kwemagetsi, nezvimwe.

OFFSET
Chinhu chinobvumira mushandisi kuita zvigadziriso zvidiki muchiratidzo chePV. Inobvumira kugadzirisa kuyerwa kukanganisa kunoonekwa, semuenzanisoample, kana uchitsiva tembiricha sensor.

USB INTERFACE 

Iyo USB interface inoshandiswa kuCONFIGURE, MONITOR kana UPDATE mutongi FIRMWARE. Mushandisi anofanira kushandisa QuickTune software, inopa maitiro ekugadzira, view, chengetedza uye vhura zvigadziriso kubva pachigadzirwa kana files pakombiyuta. Chishandiso chekuchengetedza nekuvhura zvigadziriso mukati files inobvumira mushandisi kutamisa marongero pakati pemidziyo uye kuita makopi ekuchengetedza. Kune chaiwo mamodheru, QuickTune inobvumira kuvandudza iyo firmware (yemukati software) yemutongi kuburikidza ne USB interface. Nezvinangwa zvekuTARIRA, mushandisi anogona kushandisa chero supervisory software (SCADA) kana laboratory software inotsigira iyo MODBUS RTU kutaurirana pamusoro peiyo serial yekutaurirana chiteshi. Kana yakabatana ne USB yekombuta, controller inozivikanwa seyakajairwa serial port (COM x). Mushandisi anofanira kushandisa QuickTune software kana kubvunza DEVICE MANAGER paWindows Control Panel kuona COM port yakapihwa mutongi. Mushandisi anofanirwa kubvunza mepu yeMODBUS ndangariro mucontroller's communication manual uye zvinyorwa zve supervision software kuti utange MONITORING process. Tevedza maitiro ari pazasi kuti ushandise USB kutaurirana kwemudziyo:

1. Dhawunirodha QuickTime software kubva kune yedu websaiti uye woiisa pakombuta. Iwo madhiraivha e USB anodiwa pakushandisa kutaurirana anozoiswa nesoftware.
2. Batanidza tambo ye USB pakati pemudziyo nekombuta. Mutongi haafaniri kubatanidzwa kune magetsi. Iyo USB ichapa simba rakakwana rekushandisa kutaurirana (mamwe mabasa echishandiso anogona kusashanda).
3. Mhanyai QuickTune software, gadzirisa kutaurirana uye tanga kuzivikanwa kwechigadzirwa.

Iyo USB interface HAINA KUSIYANA neiyo yekuisa chiratidzo (PV) kana yedhijitari yedhijitari yekupinda uye zvinobuda. Yakagadzirirwa kushandiswa kwenguva pfupi panguva yeCONFIGURATION uye MONITORING nguva. Nekuchengetedzwa kwevanhu nemidziyo, inofanirwa kushandiswa chete kana chidimbu chemudziyo chabviswa zvachose kubva kune yekupinza / kubuda masaini. Kushandisa USB mune chero imwe mhando yekubatanidza kunogoneka asi kunoda kunyatsoongororwa nemunhu ane basa rekuiisa. Kana ONGORORO yenguva yakareba uye iine zvakabatana zvekushandisa uye zvinobuda, isu tinokurudzira kushandisa iyo RS485 interface.

OPERATION

Iyo controller's front panel, ine zvikamu zvayo, inogona kuoneka muFig. 02:

Mufananidzo 02 -Kuzivikanwa kwezvikamu zvichireva kumberi kwepaneru

Ratidza: Inoratidza chiyero chakayerwa, zviratidzo zvemagadzirirwo maparamita uye anoenderana maitiro / mamiriro.

COM Indicator: Inopenya kuratidza chiitiko chekukurukurirana muRS485 interface.

TUNE Indicator: Gara WAKARIRA apo controller iri mukugadzirisa. OUT Indicator: Kune relay kana pulse control kubuda; inoratidza mamiriro chaiwo ezvakabuda.

A1 uye A2 zviratidzo: Ratidza kuitika kwearamu mamiriro.

P kiyi: Inoshandiswa kufamba nepakati pemenu paramita.

Kuwedzera kiyi uye Decrement kiyi: Bvumira kushandura kukosha kweiyo parameter.

Back kiyi: Inoshandiswa kudzoreredza parameters.

TANGA
When the controller is powered up, it displays its firmware version for 3 seconds, after which the controller starts normal operation. The value of PV and SP is then displayed and the outputs are enabled. In order for the controller to operate properly in a process, its parameters need to be configured first, such that it can perform accordingly to the system requirements. The user must be aware of the importance of each parameter and for each one determine a valid condition. The parameters are grouped in levels according to their functionality and operation easiness. The 5 levels of parameters are: 1 – Operation / 2 – Tuning / 3 – Alarms / 4 – Input / 5 – Calibration The “P” key is used for accessing the parameters within a level. Keeping the “P” key pressed, at every 2 seconds the controller jumps to the next level of parameters, showing the first parameter of each level: PV >> atvn >> fva1 >> type >> pass >> PV ... Kuti uise imwe nhanho, ingo sunungura kiyi ye "P" kana yekutanga parameter inoratidzwa. Kuti ufambe nepakati pemaparamendi pamwero, dzvanya kiyi "P" nekurova mapfupi. Kuti udzokere kune yakapfuura parameter mudenderedzwa, tinya: Imwe neimwe paramende inoratidzwa nekukasira kwayo muratidziro yepamusoro uye kukosha / mamiriro mune yakaderera kuratidza. Zvichienderana nehuwandu hwekuchengetedzwa kweparamendi yakagamuchirwa, parameter PASS inotungamira yekutanga parameter munhanho iyo kudzivirira kunoshanda. Ona chikamu Chekuchengetedza Kudzivirirwa.

TSANANGURO YEMAPARAMETER

OPERATION CYCLE 

TUNING CYCLE 

ARMS CYCLE 

INPUT CYCLE 

CALIBRATION CYCLE
Ese marudzi ekuisa anoyerwa mufekitori. Kana kudzokorora kuchidikanwa; ichaitwa nenyanzvi. Kana kutenderera uku kukapinda netsaona, usaite shanduko mumaparamita ayo.

CONFIGURATION KUDZIVIRIRA

Iyo controller inopa nzira yekudzivirira iyo paramita masisitimu, isingabvumire kugadziridzwa kune kukosha kweiyo paramita, uye kudzivirira t.ampkukanganisa kana kunyengedza kusina kunaka. Iyo parameter Dziviriro (PROt), muchikamu cheCalibration, inosarudza nzira yekudzivirira, ichidzikamisa kupinda kune mamwe mazinga, sezvakaratidzwa neTafura 04.

ACCESS PASSWORD
Iwo mazinga akadzivirirwa, kana awanikwa, anokumbira mushandisi kuti ape iyo Access Password yekupa mvumo yekushandura magadzirirwo emaparamita pamazinga aya. Iyo yekukurumidza PASS inotungamira maparamita pamazinga akachengetedzwa. Kana pasina password yakaiswa, iyo parameter yemazinga akachengetedzwa anogona kungoonekwa chete. The Access Password inotsanangurwa nemushandisi muparameter Password Shanduko (PAS.(), iripo muCalibration Level. Iyo fekitori yakamira papassword code ndeye 1111.

PROTECTION ACCESS PASSWORD
Iyo yekudzivirira sisitimu yakavakirwa mudhiraivha inovharira maminetsi e10 kuwana kune yakadzivirirwa paramita mushure me5 inoteedzana kuyedza kukanganisika yekufungidzira iyo chaiyo password.

MASTER PASSWORD
Iyo Master Password yakagadzirirwa kubvumira mushandisi kutsanangura password nyowani kana yakanganwa. Master Password haapi mukana kune ese ma parameter, chete kune Password Shandura parameter (PAS().Mushure mekutsanangura password nyowani, iyo yakachengetedzwa inogona kuwanikwa (uye kugadziridzwa) uchishandisa password nyowani.Pasiwedhi inogadzirwa. nemadijiti matatu ekupedzisira esiriri nhamba yemutungamiriri akawedzerwa kunhamba 9000.ample, yemidziyo ine serial nhamba 07154321, master password ndeye 9 3 2 1.

KUTSVAGA KWEPID PARAMETERS

Munguva yekusarudza otomatiki iyo PID paramita, sisitimu inodzorwa muON/OFF muiyo yakarongwa Setpoint. Iyo auto-tuning process inogona kutora maminetsi akati wandei kuti ipere, zvichienderana nehurongwa. Matanho ekuita iyo PID auto-tuning ndeaya:

• Sarudza maitiro Setpoint.
• Gonesa auto-tuning pane parameter "Atvn", uchisarudza FAST kana FULL.

Iyo Sarudzo FAST inoita iyo tuning munguva shoma inokwanisika, nepo sarudzo FULL inopa pamberi pekurongeka pamusoro pekumhanya. Chiratidzo TUNE chinoramba chakavhenekerwa panguva yese yekugadzirisa chikamu. Mushandisi anofanira kumirira kuti tuning ipere asati ashandisa controller. Munguva ye auto-tuning nguva iyo controller inoisa oscillations kune iyo maitiro. PV inotenderera yakatenderedza yakarongwa seti uye controller inobuda inobatidza nekudzima kakawanda. Kana iyo tuning ikasaunza kudzora kunogutsa, tarisa Tafura 05 kune nhungamiro dzekugadzirisa maitiro eiyo maitiro.

Tafura 05 -Nhungamiro yekugadzirisa manyore yePID paramita

MAINTENANCE

DAMBUDZIKO NEMUTONGI
Kukanganisa kwekubatanidza uye hurongwa husina kukwana ndiwo zvikanganiso zvinowanzoitika panguva yekushanda kwemutongi. Ongororo yekupedzisira inogona kudzivirira kurasikirwa nenguva uye kukuvara. Mutongi anoratidza mamwe mameseji kubatsira mushandisi kuona matambudziko.

Mamwe mameseji ekukanganisa anogona kuratidza matambudziko ehardware anoda basa rekugadzirisa.

CALIBRATION OF THE INPUT
Zvese zvekushandisa zvakagadziridzwa fekitori uye recalibration inofanira kuitwa chete nevashandi vanokwanisa. Kana usiri kujairana nemaitiro aya usaedze kuenzanisa chiridzwa ichi. Matanho ekugadzirisa ndeaya:

• Gadzirisa mhando yekupinda kuti ienzaniswe mumhando yeparameter.
• Gadzirisa miganho yepasi nepamusoro yechiratidzo chenguva yakakura yemhando yakasarudzwa yekuisa.
• Enda kuCalibration Level.
• Isa password yekuwana.
• Gonesa calibration nekuisa YES mu (alib parameter.
• Uchishandisa siginecha yemagetsi simulator, shandisa chiratidzo chepamusoro zvishoma pane yakaderera inoratidza muganho weiyo yakasarudzwa.
• Svika iyo parameter "inLC". Nemakiyi uye gadzirisa kuverenga kwekuratidzira sekuenderana nechiratidzo chakaiswa. Wobva wadzvanya kiyi P.
• Isa chiratidzo chinoenderana nemutengo wakaderera zvishoma pane wepamusoro muganhu wechiratidzo.
  Svika iyo parameter "inLC". Nemakiyi uye gadzirisa kuverenga kwekuratidzira sekuenderana nechiratidzo chakaiswa.
• Dzokera kuOperation Level.
• Tarisa uone mhedzisiro yacho. Kana zvisina kukwana, dzokorora maitiro.

Cherechedza: Paunenge uchitarisa iyo controller calibration nePt100 simulator, teerera kune iyo simulator yediki excitation ikozvino inodiwa, iyo inogona kunge isingaenderane ne0.170 mA excitation current inopiwa nemubati.

SERIAL COMMUNICATION

Iyo controller inogona kupihwa ine asynchronous RS-485 yedhijitari yekutaurirana interface yeatenzi-muranda yekubatanidza kune inotambira komputa (tenzi). Mutongi anoshanda semuranda chete uye mirairo yese inotangwa nekombuta inotumira chikumbiro kukero yevaranda. Iyo kero unit inotumira kumashure mhinduro yakumbirwa. Nhepfenyuro mirairo (inomisikidzwa kune ese maratidziro mayuniti mune multidrop network) inogamuchirwa asi hapana mhinduro inodzoserwa mune iyi kesi.

ZVINHU 

• Zviratidzo zvinoenderana neRS-485 standard. MODBUS (RTU) Protocol. Mawaya maviri ekubatanidza pakati pe1 tenzi uye anosvika makumi matatu nerimwe (kutaura anosvika 31 zvinogoneka) zviridzwa mutopology yebhazi.
• Masaini ekukurukurirana akaparadzaniswa nemagetsi kubva paINPUT uye POWER zviteshi. Haina kuparadzaniswa kubva kune retransmission redunhu uye yekubatsira voltage source kana iripo.
• Maximum yekubatanidza kureba: 1000 metres.
• Nguva yekudzima: Yakakura 2 ms mushure mekupedzisira byte.
• Programmable baud rate: 1200 kusvika 115200 bps.
• Data Bits: 8.
• Parity: Kunyange, Odd kana Hapana.
• Stop bits: 1
  • Nguva pakutanga kwekupindura kutumira: yakakura 100 ms mushure mekugamuchira murairo. Iwo RS-485 masaini anoti:

KUGADZIRIRWA KWEZVINHU ZVINHU ZVOKUTAURIRANA
Maparamita maviri anofanirwa kugadziridzwa ekushandisa iyo serial mhando: bavd: Kukurukurirana nekukurumidza.

Prty: Parity yekukurukurirana.

addr: Kero yekukurukurirana yemutungamiriri.
REDUCED REGISTERS TABLE FOR SERIAL COMMUNICATION

Kukurukurirana Protocol
Iyo MOSBUS RTU muranda inoshandiswa. Ese maparamita anogadziriswa anogona kuwanikwa pakuverenga kana kunyora kuburikidza nechiteshi chekutaurirana. Mitemo yenhepfenyuro inotsigirwa zvakare (kero 0).
Iwo aripo Modbus mirairo ndeiyi:

• 03 – Read Holding Register
• 06 - Preset Single Register
• 05 – Kumanikidza Single Coil

Kubata Registers Tafura
Inotevera tsananguro yemarejista enhaurirano akajairwa. Kuti uwane zvizere zvinyorwa dhawunirodha iyo Rejista Tafura yeSerial Kukurukurirana muN1040 chikamu chedu webnzvimbo - www.novusautomation.com. Marejista ese ane 16 bit akasainwa integers.

KUZIVA

• A: Zvinobuda Zvimiro
  • PR: OUT1= Pulse / OUT2= Relay
  • PRR: OUT1= Pulse / OUT2=OUT3= Relay
  • PRRR: OUT1= Pulse / OUT2=OUT3= OUT4= Relay
• B: Digital Communication
• 485: Inowanikwa RS485 digital communication
• C: Power Supply yemagetsi
  • (Hapana chinhu): 100~240 Vac / 48~240 Vdc; 50 ~ 60 Hz
  • 24V: 12~24 Vdc / 24 Vac

SECIFICATIONS

DIMENSIONS: ……………………………………… 48 x 48 x 80 mm (1/16 DIN)
Cheka-kunze mupaneru: …………………… 45.5 x 45.5 mm (+0.5 -0.0 mm)
Zvinorema Zvinorema: ………………………………………………………………75 g

MAGETSI:
Model standard: ………………….. 100 kusvika 240 Vac (±10 %), 50/60 Hz
………………………………………………………………. 48 kusvika 240 Vdc (±10%)
Muenzaniso 24 V: ……………………. 12 kusvika 24 Vdc / 24 Vac (-10 % / +20 %)
Kunyanya kushandisa: ……………………………………………………….. 6 VA

ZVINHU ZVAKAITIKA
Operation Temperature: …………………………………………….. 0 kusvika 50 °C
Relative Humidity: …………………………………………………… 80 % @ 30 °C
Pamatembiricha ari pamusoro pe30 °C, deredza 3 % pane yega yega °C
Kushandiswa kwemukati; Chikamu chekuisa II, Dhigirii yekusvibiswa 2;
urefu <2000 metres

INPUT …… Thermocouples J; K; T uye Pt100 (maererano neTafura 01)
Kugadziriswa Kwemukati:…………………………………….. 32767 mazinga (15 bits)
Resolution of Display: ……… 12000 mazinga (kubva -1999 kusvika 9999)
Chiyero cheKuverenga kweKupinza: …………………………………. kumusoro gumi pasekondi (*)
Kururama: . Thermocouples J, K, T: 0,25 % yenguva ±1 °C (**)
……………………………………………………………. Pt100: 0,2% yenguva
Input Impedance: ………………… Pt100 uye thermocouples: > 10 MΩ
Kuyerwa kwePt100: ………………………. 3-waya mhando, (α=0.00385)
Nemubhadharo wehurefu hwetambo, kunakidzwa ikozvino kwe0.170 mA. (*) Kukosha kunogamuchirwa kana Digital Filter parameter yakaiswa ku 0 (zero) kukosha. Kune Digital Sefa ukoshi kunze kwe0, iyo Input Reading Rate kukosha ndeye 5 sampzvishoma pasekondi. (**) kushandiswa kwe thermocouples kunoda nguva shoma yenguva ye15 maminetsi ekudzikamisa.

ZVINOGONESESA:

• OUT1: …………………………………….. Voltage pulse, 5 V / 50 mA max.
• OUT2: …………………………….. Relay SPST; 1.5 A / 240 Vac / 30 Vdc
• OUT3: …………………………….. Relay SPST; 1.5 A / 240 Vac / 30 Vdc
• OUT4: ……………………………….. Relay SPDT; 3 A / 240 Vac / 30 Vdc
  KUMASHURE PANEL: ………………………. IP65, Polycarbonate (PC) UL94 V-2
  KUKOSHESA: ……………………………………………. IP20, ABS+PC UL94 V-0
  ELECTROMAGNETIC COMPATIBILITY: …………… EN 61326-1:1997 uye EN 61326-1/A1:1998
  EMISSION: ……………………………………………………… CISPR11/EN55011
  KUDZIVIRIRA: …………………. EN61000-4-2, EN61000-4-3, EN61000-4-4,
  EN61000-4-5, EN61000-4-6, EN61000-4-8 and EN61000-4-11
  KUchengetedzwa: …………………….. EN61010-1:1993 uye EN61010-1/A2:1995

AKASIYANA CONNECTIONS FOR TYPE FORK TERMINALS;
PROGRAMMABLE CYCLE YEPWM: Kubva pa0.5 kusvika ku100 seconds. TANGA UP OPERATION: Mushure memasekonzi matatu akabatana kune magetsi. CERTIFICATION: uye.

WARRANTY

Zvinyorwa / Zvishandiso

itsnsor N1040 Temperature Sensor Controller [pdf] Bhuku reMirayiridzo N1040, Temperature Sensor Controller, Sensor Controller, Temperature Controller, Controller, N1040

References

• User Manual