Basic Wireless Switch Kit
Installation Guide

USATI WATANGA:

Kuchenjerera
-Ichi chigadzirwa chakagadzirirwa kushandiswa chete mumba uye munzvimbo dzakaoma.
-Isa & shandisa maererano nemirayiridzo iyi, magetsi makodhi, uye mitemo.
-Kana iwe uchinzwa usina chokwadi kana kusagadzikana nechero chikamu chemirairo iyi, bvunza mugadziri wemagetsi.
Inosanganisirwa muKit iyi
1 - Single Rocker Wireless Switch
1 – SA Receiver
1 - Screwless faceplate
1 - Backplate yekuisa pamusoro
2 - 3/8 ″ Backplate attachment screws
2 - 3/4 ″ Junction bhokisi rinoisa screws
2 – Command Strips ®
3 – Waya Nzungu
Uchada
-Mutyairi wePhillips Screw
-Flat Head Screw Driver kubvisa faceplate
-Blank Faceplate (inosarudza: kuvhara yekare chinja nzvimbo)
SCAN FOR INSTALL
kana kushanya:
runlesswire.com/installhttp://runlesswire.com/install

ZVINOTAURWA:

Wireless chinja

Range	50-150 ft (zvakajairika)
Frequency	902 MHz
Magetsi	Kuzvigadzira kana switch yadzvanywa
Mabhatani	2 mabhatani (1 Rocker)
Output Channels	Batanidza kune chero nhamba yevanogamuchira muhuwandu
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inchi
Radio Certification	FCC (United States)
Addressing	Factory set yakasarudzika ID (1 ye4 Bhiriyoni)

5 AMP Receiver

Range	50-150 ft (zvakajairika)
Frequency	902 MHz
Power Supply Input Rating	100-240 VAC 50/60 Hz
Relay Output	1 Fomu A Relay 10A
Max Mitoro / Contact Ratings	Resistive Load 10A Tungsten 1000W Fluorescent 600W LED Lamp 200W
Memory	Batanidza kusvika ku5 Swichi
Operating Temp	-40 kusvika 104 Madhigirii F (-40 kusvika 60 Madhigirii C)
Dimensions	1.1(L) x 1.6(W) x 3.3(H) inches
Radio Certification	FCC (United States)

NZIRA YEKUISA THE RECEIVER PACHIYEDZO FIXTURE:

1. Dzimisa breaker OFF yedunhu rauchange uchishanda Pariri.
2. Unscrew fixture kuti uwane waya.
3. Batanidza waya dzekugamuchira kune tambo dzekugadzirisa.
4. Vhura iyo breaker ON kuti uedze switch, wozodzoka OFF usati waisa waya uye inogamuchira mubhokisi rejunction. Wobva wabatanidza gadziriso, uye dzosera iyo breaker ON kuti ushandise.

Ona rimwe divi kune mirairo yekumisikidza switch

NZIRA YEKUISA RECEIVER PAZVINHU ZVINOSHANDISA:

1. BIMA muputsi wedunhu rauchange uchishanda pariri. 
2. Unscrew switch kubva kumadziro kuti uwane waya. Ndokumbira utarise: Kana pasina waya dzisina kwayakarerekera pano, unofanirwa kuisa panzvimbo yekumisikidza.
3. Bvisa waya kubva pachinja uye batanidza waya dzekugamuchira kune waya dzekuchinja.
4. Batidza breaker ON kuti uedze switch, wobva wadzima usati wapinza waya uye inogamuchira mubhokisi rejunction. Dzorera breaker kumashure kuti ushandise.

NZIRA YEKUGADZIRA Switchch:

Mount switch pane chero nzvimbo yakati sandara:
A. Shandisa 3/8″ (madiki) screws kubatanidza switch kubackplate.
B. Dzvanya faceplate pane switch.
C. Shandisa mitsetse yekuraira kukwira pane chero nzvimbo yakati sandara.Mount panzvimbo yepakutanga chinja:
A. Shandisa masiruuru 3/4” (kurebesa) kugadzika switch pabhokisi repajunction riripo.
B. Dzvanya faceplate pane switch. Backplate haidiwe.

KUTAMBURA ZVINHU:

Simbisa kuti mugamuchiri ane waya nemazvo uye anoshanda Edzai chimiro chemwenje pane anogamuchira nekudzvanya bhatani reCTRL. Green zvinoreva kuti chinobuda ngachive ON, OFF zvinoreva kuti chinobuda ngachive OFF. Chiyereso cheStatus chisiri kushanda chinoratidza kuti simba harina ON, wiring haina kunaka, kana kuti inogamuchira yakakuvadzwa. Kana mwenje wechimiro ukabatidza, asi mwenje ukasabatidza, wiring inogona kunge isiriyo kana kutadza kushanda kwegirobhu.
Confirm switch inoshanda
Dzvanya kumusoro kwechibatiso kuti uvhure mugamuchiri ON uye pazasi pechibatiso kuti udzime. Kana mugamuchiri akasapindura, switch inogona kunge isina kubatana.
Batanidza switch kune inogamuchira:

1. Dzvanya bhatani pane inogamuchira kwemasekonzi matatu kusvika mugamuchiri atanga kubatidza / kudzima.
2. Dzvanya TOP yekuchinja 3 nguva nekukurumidza kuti ubatanidze switch kune controller, kana BOTTOM yekuchinja 3 nguva kuti usunungure.
3. Iyo LED uye inobuda ichamira ON kwemasekonzi matatu kana yakabatana, kana KUDZIMA kwemasekonzi matatu kana isina kubatana.
4. Mirira iyo yekubatanidza modhi kuti ipedze nguva (30 masekondi), kana simba kutenderera switch.
5. Yedza switch kuti uone kuti yakabatana nemazvo.

FCC Yambiro
Ichi chishandiso chinoenderana nechikamu 15 cheFCC Mitemo. Kushanda kunoenderana nemamiriro maviri anotevera: (1) Muchina uyu haugone kukonzera kukanganisa kunokuvadza, uye (2) mudziyo uyu unofanirwa kugamuchira chero kukanganisa kunowanikwa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingade.
Cherechedza: Midziyo iyi yakaedzwa uye yakawanikwa inoenderana nemiganhu yeKirasi B yedhijitari mudziyo, zvichienderana nechikamu 15 cheFCC Mitemo. Iyi miganho yakagadzirirwa kupa dziviriro inonzwisisika kubva mukukanganisa kunokuvadza mukuiswa kwekugara. Mudziyo uyu unogadzira, unoshandisa uye unogona kuvheneka redhiyo frequency simba uye, kana isina kuiswa uye kushandiswa zvinoenderana nemirairo, inogona kukonzera kukanganisa kunokanganisa kufambiswa kweredhiyo. Nekudaro, hapana vimbiso yekuti kukanganisa hakuzoitika mune imwe yekumisikidza. Kana mudziyo uyu ukakonzera kukanganisa kunokuvadza redhiyo kana terevhizheni, iyo inogona kutariswa nekudzima uye nekubatidza mudziyo, mushandisi anokurudzirwa kuyedza kugadzirisa kukanganiswa neimwe kana anopfuura eanotevera matanho:
Reorrent kana kutamisa antenna inogamuchira.
Wedzera kupatsanurwa pakati pemidziyo nemugamuchiri.
Batanidza midziyo mune yekubuda padunhu rakasiyana neiyo iyo inotambirwa yakabatana.
Bvunza mutengesi kana nyanzvi yeredhiyo/TV ine ruzivo kuti ubatsirwe.
Cherechedza: Mubatsiri haakonzeri chero shanduko kana gadziridzo dzisina kubvumidzwa nebato rine chekuita nekutevedzwa. kugadziridza kwakadaro kunogona kukanganisa mushandisi simba rekushandisa mudziyo.

HDO721A
support@runlesswire.com
866.600.2111

Zvinyorwa / Zvishandiso

RunLessWire RW95CB Basic Wireless Switch Kit [pdf] Installation Guide VJC-RW95CB, VJCRW95CB, RW95CB, RW95CB Basic Wireless Switch Kit, Basic Wireless Switch Kit, Wireless Switch Kit, Switch Kit, Kit

References

• User Manual